Fieldmox by Heffl

Free template · Western Australia · Updated November 2026

SWMS template for Western Australia

Western Australia moved to the national-model WHS laws in 2022, and its Work Health and Safety (General) Regulations 2022 require a SWMS before high risk construction work starts. The SWMS must identify the work, its hazards and risks, the control measures, and how they're implemented, monitored and reviewed. Use the free builder below.

Fill in your WA SWMS

Start blank or from a trade example, then download Word or PDF. Free, no sign-up.

Free, no sign-up. Your draft saves in this browser as you type.

1. Business and job details
2. High risk construction work

Tick every category the job involves. If none apply, a SWMS isn't legally required, but many builders still ask for one.

3. PPE, plant, licences and emergency
4. Job steps, hazards and controls

One row per step, in the order the work is done. Put each hazard and each control on its own line.

    5. Monitoring and review

    The download adds a worker sign-on table and an approval block for the principal contractor.

    SWMS law in Western Australia

    Act
    Work Health and Safety Act 2020 (WA)
    Regulation
    Work Health and Safety (General) Regulations 2022 (WA)
    Regulator
    WorkSafe WA

    What to know in WA

    • WA's WHS laws replaced the old Occupational Safety and Health Act 1984. Older WA templates written under the OSH laws should be updated.
    • The 18 high risk construction work categories and the SWMS content rules match the national model.
    • WorkSafe WA publishes an information sheet on SWMS for high risk construction work.

    Work that needs a SWMS in WA

    Western Australia uses the national list of 18 types of high risk construction work. A SWMS is required before any of them starts.

    1. 1 Risk of a fall of more than 2 metres
    2. 2 Work on a telecommunication tower
    3. 3 Demolition of load-bearing or structural elements
    4. 4 Disturbing asbestos
    5. 5 Structural alterations needing temporary support
    6. 6 In or near a confined space
    7. 7 Shaft or trench deeper than 1.5 m, or a tunnel
    8. 8 Use of explosives
    9. 9 On or near pressurised gas mains or piping
    10. 10 On or near chemical, fuel or refrigerant lines
    11. 11 On or near energised electrical installations
    12. 12 Contaminated or flammable atmosphere
    13. 13 Tilt-up or precast concrete
    14. 14 On or next to a road, railway or shipping lane in use
    15. 15 Where powered mobile plant is moving
    16. 16 Artificial extremes of temperature
    17. 17 In or near water with a risk of drowning
    18. 18 Diving work

    What a SWMS must include, how to fill it in, and a worked example: the full SWMS guide.

    SWMS questions for WA

    Is a SWMS required in WA?
    Yes, for high risk construction work. Under WA's WHS (General) Regulations 2022, a SWMS must be prepared before the work starts and the work must follow it.
    Can I still use an old WA safety template from before 2022?
    Check it first. Templates written under the old OSH Act may use outdated terms and miss sections the WHS laws require, such as how controls are monitored and reviewed. The builder on this page follows the current requirements.
    How long do I keep a SWMS in WA?
    Until the high risk construction work is finished, or for at least 2 years after a notifiable incident that happened during the work.

    Attach the SWMS to every job

    Fieldmox runs quotes, scheduling, the technician app and invoicing in one place. Save the SWMS on the job next to the quote and photos, so it's there when the builder asks for it, and add "SWMS read and signed" to the visit checklist your crew ticks off on their phone before they start.

    Book a meeting