Fieldmox by Heffl

Free template · Australia · Updated November 2026

Tiling SWMS template

Most tiling isn't high risk construction work, so a SWMS isn't always required by law. But builders usually ask for one, and silica dust from cutting tiles is a serious risk. This one covers moving materials, removing old tiles, cutting, mixing, laying and grouting. Tick any high risk work that applies on your job, then download it.

Edit it online

Free, no sign-up. The download adds a worker sign-on table and principal contractor approval.

The tiling SWMS

6 job steps, from set-up to pack-down. Every step lists its hazards, risk before and after, and the controls.

Work activity
Removing old wall and floor tiles and installing new ceramic and porcelain tiles in a bathroom and kitchen, including cutting, waterproofing and grouting.
High risk construction work
None by default. Tick any that apply on your job.
PPE
Safety glasses, Hearing protection, Steel-cap boots, Work gloves, Chemical-resistant gloves, P2 respirator, Knee pads
Plant and equipment
  • Wet tile saw with RCD
  • Angle grinder with dust extraction
  • Mixing paddle and drill
  • H-class vacuum
  • Trolley for tile boxes and bags
Licences and training
  • General construction induction (White Card)
  • Waterproofing licence where the state requires one
  • Silica awareness training
Job steps, hazards, risk ratings and control measures
# Job step Hazards Risk Control measures Residual Responsible
1 Move tiles, adhesive and grout
  • Back strain from heavy boxes and 20 kg bags
  • Crush injuries
Medium
  • Use a trolley; carry one box or bag at a time
  • Stack boxes low and stable
  • Every worker reads and signs this SWMS
Low All workers
2 Remove old tiles and linings
  • Asbestos in old adhesive, vinyl or fibre cement sheeting
  • Silica dust
  • Flying tile chips
  • Noise
High
  • Check the asbestos register or test suspect materials in buildings built before 1990
  • Stop and get licensed help if asbestos is found
  • Wet the area; use an H-class vacuum, not a broom
  • Wear safety glasses, a P2 respirator and hearing protection
Medium Supervisor
3 Cut tiles
  • Crystalline silica dust
  • Blade cuts
  • Electric shock from wet saws
  • Noise
High
  • Cut wet, or use on-tool dust extraction; cut outdoors where possible
  • Wear a P2 respirator, safety glasses and hearing protection
  • Plug wet saws into an RCD; keep leads out of water
  • Keep blade guards in place
Low All workers
4 Mix adhesive, grout and waterproofing
  • Cement dust and burns
  • Chemical skin irritation
  • Wrist strain from the mixing paddle
Medium
  • Pour bags slowly at low height; wear a P2 respirator
  • Wear chemical-resistant gloves and read the SDS
  • Brace the drill and start on low speed
Low All workers
5 Lay and grout tiles
  • Knee and back strain
  • Solvent fumes from some sealers
  • Slips on wet floors
Medium
  • Wear knee pads and change position often
  • Ventilate rooms when using sealers
  • Keep the floor clear and mark wet areas
Low All workers
6 Clean up
  • Silica dust from dried slurry
  • Slurry in drains
Medium
  • Vacuum with an H-class vacuum or wet wipe; never dry sweep
  • Settle slurry in a bucket and dispose of solids in the bin
Low All workers

Rules that apply to tiling work

  • Cutting, grinding and polishing tiles, stone and grout releases crystalline silica. Cut wet or with on-tool extraction and wear a P2 respirator.
  • Engineered stone is banned in Australia (from 1 July 2024 in most states). Don't cut or install it.
  • Old floor tiles, adhesives and fibre cement underlay in buildings built before 1990 may contain asbestos. Test before removing.
  • Wet saws must run through an RCD.

Questions

Do tilers need a SWMS?
Not always by law. Tiling only needs a SWMS when it involves high risk construction work, such as a fall risk of more than 2 metres or working where mobile plant is moving. Builders often require one anyway, and it's a good way to show you control silica dust.
How do tilers protect themselves from silica dust?
Cut wet or with on-tool extraction, wear a P2 respirator (or better), cut outdoors where you can, and clean up with an H-class vacuum or wet methods. Dry cutting without controls is the main cause of silicosis in the trade.
Can I still cut engineered stone?
No. Engineered stone benchtops, panels and slabs have been banned from use in Australia since 2024. Removal, repair and disposal of existing engineered stone is still allowed, with silica controls.
Is this tiling SWMS free to use?
Yes. Download it as Word or PDF with no sign-up, or open it in the online builder to change the steps and add your business details first. Check it against your own job and site before you use it.

Attach the SWMS to every job

Fieldmox runs quotes, scheduling, the technician app and invoicing in one place. Save the SWMS on the job next to the quote and photos, so it's there when the builder asks for it, and add "SWMS read and signed" to the visit checklist your crew ticks off on their phone before they start.

Book a meeting